L. Kh. Kogan, A. N. Stashkov

CAPABILITIES OF EDDY CURRENT NDT OF SOLDERED CURRENT-CARRYING JOINTS IN SUBMERSIBLE ELECTRICAL EQUIPMENT FOR OIL AND GAS INDUSTRY

The paper shows the possibility to test the quality of soldering of small current-carrying non-ferromagnetic joints in submersible electrical equipment for oil and gas systems by the amplitude eddy current method using a highly sensitive primary transducer with a U-shaped core. The sensitivity of soldering quality testing under different conditions of generating an exciting signal is compared. It has been found that the sensitivity of NDT in the case of current amplitude stabilized in the excitation coil (current generator) is significantly higher than that in case of voltage amplitude stabilized in it (voltage generator). Possible errors in determining the level of soldering of the joints due to the variation of their cross section within the limits of tolerance according to the technology of their manufacture have been detected. Circuit solutions and software have been developed to test the level of soldering of such joins. Approbation of soldering quality testing was carried out on products manufactured under production conditions.

Acknowledgment: The reported study was funded by the Ministry of Science and Higher Education of the Rus-sian Federation (theme Diagnostics, No. 122021000030-1).

References:

1. Rozenfeld, E.V., Nichipuruk, A.P., Kogan, L.Kh., and Khudyakov, B.A. Eddy-current quality control of soldering of current-carrying joints in electrical machines. I. General principles. Russian Journal of Nondestructive Testing, 2010, 46 (4), 281–291. DOI: 10.1134/S1061830910040066.
2. Khromchenko, G.E. Soedinenie i Okontsevanie Mednykh i Aluminievykh Provodov i Kabeley [Connection and Termination of Copper and Aluminum Wires and Cables]. Gosenergoizdat Publ., Moscow–Leningrad, 1962, 49 p. (In Russian).
3. Principe, R., Vallejo, L.M., Bailey, J., Berthet, R., Favier, L., Grand-Clement, L., and Savary, F. Phased array ultrasonic nondestructive tests of soldered current-carrying bus-bar splices of superconducting magnets. In: IEEE Transactions on Applied Superconductivity, June 1–8, 2018, IEEE, 2018, 28 (4), 9000708. DOI: 10.1109/TASC.2018.2800735.
4. Malyy, V.V., Kostyukhin, A.S., and Kinzhagulov, I.Y. Development of technology for non-destructive quality control of heat exchanger brazed joints and determination of the principles of its automation. Tekhniko-Tekhnologicheskie Problemy Servisa, 2022, 3 (61), 11–17. (In Russian).
5. Maierhofer, Ch., Röllig, M., Steinfurth, H., Ziegler, M., Kreutzbruck, M., Scheuerlein, Ch., and Heck, S. Non-destructive testing of Cu solder connections using active thermography. NDT & E International, 2012, 52, 103–111. DOI: 10.1016/j.ndteint.2012.07.010.
6. Kogan, L.Kh., Nichipuruk, A.P., Rozenfeld, E.V., and Khudyakov, B.A. Eddy-current quality control of soldering of current-carrying joints in electrical machines. II. Experiment. Russian Journal of Nondestructive Testing, 2010, 46 (4), 292–301. DOI: 10.1134/S1061830910040078.
7. Syasko, V.A., Roitgarts, M.B., Koroteev, M.Yu., and Solomenchuk, P.V. Quality testing of soldered joints of turbogenerator stator winding cores at the “Elecktrosila” plant. V Mire Nerazrushayushchego Kontroya, 2010, 2 (56), 40–43. (In Russian).
8. Koroteev, M.Yu. Calculation of eddy current probe parameters for quality control of turbine generators rods winding soldering. Estestvennye i Tekhnicheskie Nauki, 2014, 2, 195–204. (In Russian).
9. Potapov, A.I., Syasko, V.A., Koroteev, M.Yu., and Solomenchuk, P.V. A Finite-element modeling of a probe of eddy-current quality testing of soldered joints in turbogenerator windings. Russian Journal of Nondestructive Testing, 2014, 50 (5), 264–273. DOI: 10.1134/S1061830914050064.
10. Fedosenko, Yu.K., Shkatov, P.N., and Efimov, A.G. Vikhretokovyy Kontrol [Eddy Current Testing: Educational Book]. Spektr Publ., Moscow, 2011, 224 p. (In Russian).
11. Dorofeev, A.L. Elektro-Induktivnaya Defektoskopiya [Electroinductive (Induction) Flaw Detection]. Mashinostroenie Publ., Moscow, 1967, 231 p. (In Russian).
12. Syasko, V.A. and Chertov, D.N. Lamination detection in carbon fiber reinforced plastics with the use of tangential eddy current transducers. V Mire Nerazrushayushchego Kontrolya, 2012, 2 (56), 19–21. (In Russian).
13. Ge, J., Yusa, N., and Fan, M. Frequency component mixing of pulsed or multi-frequency eddy current testing for nonferromagnetic plate thickness measurement using a multi-gene genetic programming algorithm. NDT & E International, 2021, 120, 102423. DOI: 10.1016/j.ndteint.2021.102423.
14. Sidi-Ahmed, K., Maouche, B., Gabi, Y., Alloui, L., Straß, B., Wolter, B., and Feliachi, M. Numerical simulations and experimental investigation of laser hardening depth investigation via 3MA-eddy current technique. Journal of Magnetism and Magnetic Materials, 2022, 550, 169046. DOI: 10.1016/j.jmmm.2022.169046.
15. Reutov, Yu.Ya. On joint application of permanent and alternating fields in magnetic detection of defects in thick-walled steel products. Russian Journal of Nondestructive Testing, 2022, 58 (12), 1129–1141. DOI: 10.1134/S1061830922700139.

Article reference